- #How to configure password encryption on cisco 2950 switch how to
- #How to configure password encryption on cisco 2950 switch software
- #How to configure password encryption on cisco 2950 switch password
- #How to configure password encryption on cisco 2950 switch mac
NOTE: this is the IP we are going to use to connect to this switch using our broswer for the web interface Management network from the above interface summary: FastEthernet0/24 (Or set whatever Interface you want)Ĭonfigure IP on this interface? : yes
#How to configure password encryption on cisco 2950 switch password
The virtual terminal password is used to protectĪccess to the router over a network interface.Įnter virtual terminal password(enter whatever you want your password to be)Įnter interface name used to connect to the
#How to configure password encryption on cisco 2950 switch software
The enable password is used when you do not specify anĮnable secret password, with some older software versions, andĮnter enable password(enter whatever you want your enable password to be) This password, afterĮntered, becomes encrypted in the configuration.Įnter enable secret : (enter whatever you want your secret password to be) The enable secret is a password used to protect access to Would you like to enter basic management setup? : noįirst, would you like to see the current interface summary? : noĮnter host name (enter whatever you want to name your switch) Now you are back to the promp and enter this command:Ĭontinue with configuration dialog? : no Now that the flash OIS has been initialized, select 'boot' from the main and hit enter on your keyboard, the switch will start to load the OS until you get to a message that says: Press RETURN to get started! Parameter Block Filesystem (pb:) installed, fsid: 4 Now the setting has been set to factory defaults:įlashfs: 0 orphaned files, 0 orphaned directoriesīoot Sector Filesystem (bs:) installed, fsid: 3 The flash filesystem, and finish loading the operatingĮnter: flash_init and hit Return on your keyboardĪfter you select flash_init you will see a message: Initializing Flash. The system has been interrupted prior to initializing theįlash filesystem.
#How to configure password encryption on cisco 2950 switch how to
Here is how to view the vlan configuration.Ok now that we have connected to the switch using hyperterminal and you are at the main flash menu: you should see something that looks like this:Ġ0:00:17: %SYS-5-CONFIG_I: Configured from memory by consoleĠ0:00:17: %SYS-5-RESTART: System restarted -Ĭisco Internetwork Operating System Software This is very easy to do and an essential part of learning Cisco CCNA certifications. Now you may enter any changes you wish to make to create your VLAN and routing setups with a fresh vanilla switch setup. (c) (1) (ii) of the Rights in Technical Data and Computer (c) of the Commercial Computer Software - Restricted
#How to configure password encryption on cisco 2950 switch mac
Would you like to enter the initial configuration dialog? : nĠ0:03:17: %SYS-5-RELOAD: Reload requestedĬ2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)īase ethernet MAC Address: 00:0e:84:d8:b3:40įlashfs: 0 orphaned files, 0 orphaned directoriesīoot Sector Filesystem (bs:) installed, fsid: 3 Motherboard assembly number: 73- 5781- 12
Image text-base: 0x80010000, data-base: 0x805C0000Ĭisco WS-C2950- 24 (RC32300 ) processor (revision M0 ) with 20710K bytes of memory.Ģ4 FastEthernet /IEEE 802.3 interface (s )ģ2K bytes of flash-simulated non-volatile configuration memory.īase ethernet MAC Address: 00:0E: 84:D8:B3: 40 252.227- 7013.Ĭisco Internetwork Operating System Software (c ) ( 1 ) (ii ) of the Rights in Technical Data and Computer (c ) of the Commercial Computer Software - Restricted Subject to restrictions as set forth in subparagraph Use, duplication, or disclosure by the Government is
#įile "flash:/" uncompressed and installed, entry point: 0x80010000 Parameter Block Filesystem (pb: ) installed, fsid: 4
00:03: 17: %SYS- 5-RELOAD: Reload requestedĬ2950 Boot Loader (C2950-HBOOT-M ) Version 12.1 (11r )EA1, RELEASE SOFTWARE (fc1 )Ĭompiled Mon 22-Jul-02 17: 18 by antoninoīase ethernet MAC Address: 00:0e: 84:d8:b3: 40įlashfs : 0 orphaned files, 0 orphaned directoriesįlashfs : flashfs fsck took 7 seconds.īoot Sector Filesystem (bs: ) installed, fsid: 3
0 kommentar(er)
